PCPartPicker

  • Log In
  • Register

Comments

Jinair's Completed Build: Evolv X Dual System. 8086k+1080ti SLI and Ryzen 2700x+2080ti in a single case.

yookehjohn 2 Builds 1 point 3 months ago

That racing rig setup sounds so dreamy. Definitely interested to see pictures of how the rig looks!

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 1 point 3 months ago

oh and btw, your build is stunning.

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 1 point 3 months ago

Thanks for the tip, yeah the GPU fans will start to spin a bit faster during prolonged gaming.

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 1 point 4 months ago

thank you!

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 1 point 4 months ago

thanks!

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 3 points 4 months ago

yes she does! wife points and says "that one" and i say ok!

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 1 point 4 months ago

thanks buddy! i'm the lucky one. since switching over her k:d has been going up!

yookehjohn's Completed Build: Wifey Black Friday Build

yookehjohn submitter 2 Builds 3 points 4 months ago

nothing more true than that in life. thanks!

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 4 months ago

not too many problems, just a bit of shoving it up against the IO shield but it went in fine.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 2 points 6 months ago

Not a problem, glad you made it work.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 2 points 6 months ago

The motherboard you picked is ATX and should fit in the case with no rear fan clearance problems. You might want to make sure that the motherboard is on the standoffs that came with the case. You do not need to install additional standoffs. Make sure that the shroud with all the rear connectors on the motherboard are aligned with the cutout in the back of the case. It took me a little bit to make sure those two were aligned.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 2 points 7 months ago

Yes it did. I ended up with an extra as the 3 ll120 pack came with one also.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 8 months ago

You could go with the 1000D though

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 8 months ago

No sorry, I think it only goes up to ATX

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 8 months ago

I had a fan related error codes that I had to fix though before being able to boot up but other than that it was fine.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 2 points 9 months ago

Thanks!

When I had some cable clutter the clearance of the cables in the back prevented the door from closing. But since I cleaned up the cables I haven't had any issues with keeping the door closed.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 9 months ago

Thanks Napalm

I mounted the m.2 in the bottom slot just to make it visible. I could have installed it under the heat shield.

The CPU cooler is mounted at the front of the case and I have the GPU cooler mounted at the rear of the case. Not sure what you mean?

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 9 months ago

Thanks, I really like how your cable management turned out. Definitely better than mine!

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 9 months ago

I did not have to order custom cables as the cables that came with my power source were already white. But I know that you can buy different color cables from Corsair or Phanteks. Hope this helps.

IrishWristwatch's Completed Build: Den Grå Maskinen

yookehjohn 2 Builds 2 points 9 months ago

very clean build, you definitely did a good job with the cable management

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 9 months ago

That's how similar they look actually. On the 500D RGB SE, the power source shroud covers the entire power source and isn't open ended like the 570x. The 500D RGB SE also doesn't have the thumb screws on the glass panels as the side panels have a hinge and the front panel is not removable.

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 1 point 9 months ago

I was thinking about doing the 570x but went for an Obsidian 500D RGB SE instead

yookehjohn's Completed Build: Panda Corsair Build

yookehjohn submitter 2 Builds 2 points 9 months ago

lol thanks :)

Page
1